Conexão de Cabos e TP na Martech Clip

[ligteltelecom]

Como usar o Clip da Martech com adaptador de Testpoint ligado no Clip -
No Modo Box II (PC)


Complet includes:




A - Martech CLIP device
B - x65/x75 converter cable
C - transmition cable (direct cable) for phone
D - testpoint cable
E - SGOLD phone's PCB


How to connect CLIP equipment (SGOLD phones):




How to use MARTECH SIEM Service Tools with Martech CLIP (Testpoint Adapter builded in Clip)




- run newest Martech SIEM Service Tools program
- select phone type
- select "Testpoint Adapter builded in CLIP" mode
- click any function (for example "Read Phone" button)



- look at picture with testpoint location details
- check phone powering connections (RED connector)
- select correct boot/testpoint variant (variant 1 is auto selected)



- Connect testpoint probe (needle) to test points on phone's PCB

If states will show "Connected OK" application will automatically boot phone...
Keep testpoint connectors connected until program will let you remove them.
For S65,Sv65,S66,SK65,CX75,M75,CF75 you have to use Manual mode (this mode is auto selected). This mode needs using switch on black probe...

Remember that with some older versions of SGOLD phones (with SW version lower than 36), you can work in DIRECT MODE (without any testpoints).
Just use full charged battery for powering phone...


Como usar o Clip da Martech com adaptador de Testpoint ligado no Clip -
No Modo CLIP sem uso de PC


Complet includes:




A - Martech CLIP device
B - x65/x75 cable converter
C - transmition cable (direct cable) for phone
D - testpoint cable
E - SGOLD phone's PCB


How to connect CLIP equipment (SGOLD phones):




How to use MARTECH SIEM Service Tools - CLIP Edition




- run the newest Martech SIEM Service Tools - CLIP Edition
- select phone type
- select "CLIP builded in adapter" mode
- click F2 button (Assigned to "OK")




- Connect testpoint probes (needles) to test points on phone pcb.



If states will show "Connected OK" application will automatically boot phone...
Keep testpoint connectors connected until program will let you remove them.
For S65,SV65,S66,SK65,CX75,M75,CF75 you have to use Manual mode (this mode is auto selected). This mode needs using switch on black probe...


Como usar o Clip da Martech com Testpoint Adapter Versão 2.0 /3.0 ligado no Clip - No Modo Clip sem uso de PC



Complet includes:



A - Martech CLIP device
B - Testpoint Adapter v3.0
C - cable for connection Martech BOX with TP adapter
D - x65/x75 cable converter
E - transmition cable (direct cable) for phone
F - testpoint cable
G - EGOLD phone's PCB


How to connect CLIP equipment (EGOLD phones):




How to use MARTECH SIEM Service Tools - Clip Edition




- run the newest Martech SIEM Service Tools - Clip Edition program
- select phone type
- select "TP Adapter v2.0 / v3.0" mode
- click F2 button (Assigned to "OK")
- connect testpoint probes (needles) to test points on phone's PCB



If states will show "Connected OK" application will automatically boot phone...
Keep testpoint connectors connected until program will let you remove them.



If you have problem with autodetection - just select "Manual mode", connect needles to phone's test points, and press switch on black probe...

Regards

[oficinadocelular1]

Administrador ligteltelecom poderia reparar as imagem pois não estão disponiveis, Semprei utilizei a Dream box , mas agora estou trabalhando em outra oficina onde tem a Martech , quando clico na opção unlock aparece a foto indicando dois pontos para fazer test point e o meu cabo só tem agulha pra fazer o test point ,juntamente com um plug conhecido como jacarezinho pra conectar no positivo do aparelho e outra na outra ponta um pino que parace que e para ser conectado na fonte de alimentaçao .
Alguem poderia me da uma dica ?