Atualizações Cyclone Box - cyclone team

[derbetty]

Cyclone EVOLUTION ! Added FREE Clip Mode, Added FREE Infineon XGold Flashing & More..
Hi to all
New Cyclone Box Installer, Firmware, Bootloader, is ready!
Most important changes:

=====================
Installer v1.07
30.06.2010
=====================
- New FBUS Loaders v10.18.00 introduced (new protocol, for RAPIDO,RAPU,ST,etc)
- New FBUS Lodaers v10.16.00 introduced (old protocol, for RAPv3)
- Added support for Infineon X-Gold phones flashing. Phones supported: 1661 RH-111, RH-125, etc.
- XGold: Support for dead phones flashing
- XGold: Support for cross flash (we have tested 1616 flashing with 1800 firmware and seems works. Anyway YOU are responsible for any damages. Make sure PM is being backed-up before cross-flash. You also can't flash phones with difrent platform (i.e. RH111 <> RH125). Too diffrent CPU, LCD...,etc...)
- XGold: Supports bauds 115200,230400,460800,921600
- XGold: You don't need to know which phone is UPP or Infineon based. Just select model and Cyclone will detect it automaticly - wil select corect falshing method.
- XGold: Supports for changing phone PPM/CNT or/and MCU
- XGold: Support for latest 2010 PBL/EBL Loaders
- Added "Flash Language Only" checkbox for DCT4/XGold mobiles. Use only if MCU version installed in phone matches PPM/CNT version which going to be flashed.
- Cyclone Clip Diagnostic module added. This is used for testing additional Cyclone Hardware (Clip).
- Clip Module Added into Main Firmware. This is used only with "Cyclone Clip" hardware. Clip Features:
- Clip: Can unlock any DCT4+ phone within 2 secs (without PC)
- Clip: Can repair Contact Service (if caused by damaged simlock)
- Clip: Can Rebuild Simlock Area
- Clip: Can reset security code of most DCT4/BB5 phones
- Clip: Can reset security code bad attempts counter of most DCT4/BB5 phones
- Clip: 100% Safe, fast and easy to use
- You need have Clip Hardware to use Clip Funcionality. Clip is very simple hardware attached together with batery to Diagnostic Port (and box could be used as clip without PC). We will update clip later for other funcionality.
- New Secure Bootloader Agent v3.00 Released
- Added Dead Boot Recovery mode (in case to do "Boot Recovery" (just in case) smartcard MUST be removed to launch Recovery Mode!)
- New Secure Bootloader v2.12 have been released
- Bootloader: Added Clip Detection
- Bootloader: Fixed floating (blinking) "VBAT" port
- Bootloader: Added support for some new types of smartcard
- Bootloader: Improved startup time
- Bootloader: Improved security
- Bootloader: Minor changes and bugfixes
- Added new messages to NCK Phone Respond parsing (added "Too fast between tries" and "Not locked on given locklevel")
- The +4/5/6/7 BB5 NCK passwords are now calculated correctly (memory leak during code calculation)
- Message "This will consume XX credits" removed while taking DCT4 RPL as long as they are free .
- Blackberry IMEI Check fixed
- Added "Skip CMT ID Check" for some BB5 phones (if you are trying to flash alien files or NMP made some mistake during building FIASCO images)
- Added Warning confirmation before Writing Alien SD Keys
- Error while RSA unlocking DCT4 phones fixed (Error 0x02). Error have occured when used bad cable.
- Main Firmware v01.41 Released
- Box HW Rev A11E Added
- Minor changes and bugfixes

How to run "Clip Mode"?
1. Attach Clip Adapter to box "Diagnostic Port"
2. Connect Clip Adapter "USB" cable to box USB Input
3. Connect 9V battery to Clip Adapter
4. Connect phone to "Service Port"

How to use "Clip Mode"?
Once Clip Mode is run, you need use S1 Button to change it's mode.
Default clip mode is:
RED (slowly blinking) - read phone info via FBUS
other modes you can select pressing S1 button:
GREEN - Unlock/Repair simlock
BLUE - reset securitycode/sec.code attempts

Once correct mode is assigned, you need push S2 button. Needed action will be taken, and GREEEN (success) or RED(failed) led will blink fast afterall. Clip will be ready to service next phone/select other mode/etc.

Maybe some movie, how to use it?
Youtube: [Somente usuários registrados podem ver os links. Clica aqui para se registrar...]

Where to get clip hardware?
You can ask any of Cyclone Box distributor/reseller.
Hardware is relative cheap - 15 usd (end-user price).
We will update clip soon with other functions.
It's first official Cyclone Addon.
Keep note it is CYCLONE ADDON, and same Clip Adaptor - it's just adaptor and still Cyclone Box is needed to work!

Where from download?
[Somente usuários registrados podem ver os links. Clica aqui para se registrar...]

Best Regards,
Stay Tuned,
Cyclone Team

[Beni Amaral]

TRADUÇÃO DIRETA+ANEXO!!

EVOLUTION Cyclone! Adicionado Mode Clip FREE, FREE Adicionado Infineon XGold Flashing & More ..
Oi para todos
Novo ciclone Box Installer, Firmware, Bootloader, está pronto!
A maioria das mudanças importantes:

=====================
Installer v1.07
2010/06/30
=====================
- Nova FBUS Loaders v10.18.00 introduzidas (novo protocolo, por RAPIDO, RAPU, ST, etc)
- Nova FBUS Lodaers v10.16.00 introduzidas (protocolo de idade, por RAPv3)
- Adicionado suporte para telefones Infineon X-Gold piscar. Telefones suportados: 1661 RH-111 RH-125, etc
- XGold: Suporte para telefones mortos piscando
- XGold: Suporte para flash cruz (nós testamos 1616 piscando com firmware 1800 e parece funciona. Anyway VOCÊ é responsável por quaisquer danos. Faça PM certeza está sendo feito-up antes de flash-cruz. Você também não pode flash telefones com difrent plataforma (ou seja, RH111> - XGold: Suporta bauds 115200,230400,460800,921600
- XGold: Você não precisa saber qual telefone é UPP ou Infineon base. Basta selecionar e modelo Cyclone vai detectá-lo automaticly - método falshing wil selecionar corect.
- XGold: Apoios para mudar de telefone PPM / CNT e / ou MCU
- XGold: Suporte para os últimos 2.010 PBL / EBL Carregadeiras
- Adicionado "Flash única linguagem checkbox" para telemóveis DCT4/XGold. Use somente se a versão MCU instalado no telefone partidas PPM / CNT versão que vai ser brilharam.
- Cyclone Clip módulo de diagnóstico acrescentou. Isto é usado para testes adicionais Cyclone Hardware (Clip).
- Clip Módulo Adicionado em Main Firmware. Isso é usado somente com o "Cyclone Clip" hardware. Características Clip:
- Clip: pode desbloquear qualquer celular + DCT4 dentro de 2 segundos (sem PC)
- Clip: Pode reparar Contact Service (se for causada por simlock danificado)
- Clip: É possível reconstruir Área Simlock
- Clip: É possível redefinir o código de segurança da maioria dos telefones DCT4/BB5
- Clip: É possível redefinir o código de segurança contra tentativas mal da maioria dos telefones DCT4/BB5
- Clip: 100% Seguro, rápido e fácil de usar
- Você precisa ter Clip Clip Informática usar funcionalidade. Clip é muito simples de hardware anexado juntamente com batery para diagnóstico Port (caixa e poderia ser usado como clip sem PC). Vamos atualizar clip mais tarde para outras funcionalidade.
- Nova Secure Bootloader agente v3.00 Released
- Adicionado Dead Boot modo de recuperação (caso em que fazer "Boot Recovery" (apenas no caso) smartcard deve ser removido para lançar Recovery Mode!)
- Nova Secure Bootloader v2.12 foram liberados
- Bootloader: Detecção Clip Adicionado
- Bootloader: flutuante fixo (piscando) "porto" Vbat
- Bootloader: adicionado suporte para alguns novos tipos de smartcard
- Bootloader: Maior tempo de inicialização
- Bootloader: Melhor segurança
- Bootloader: Pequenas alterações e correções
- Adicionado novas mensagens para NCK análise Responda Telefone (acrescentou: "Muito rápido entre as tentativas" e "Não é bloqueado dado locklevel")
- As senhas NCK +4/5/6 / 7 BB5 agora calculado corretamente (vazamento de memória no código de cálculo)
- Mensagem "Isso vai consumir XX" créditos removido tendo DCT4 RPL enquanto eles estão livres.
- Blackberry IMEI Check fixo
- Adicionado "Skip CMT ID Check" para alguns telefones BB5 (se você está tentando arquivos flash estrangeiro ou NMP cometido algum erro durante a construção FIASCO imagens)
- Adicionado aviso de confirmação antes de escrever Alien SD Keys
- Erro ao RSA desbloqueio DCT4 telefones fixos (Error 0x02). Erro ocorrido quando utilizado o cabo ruim.
- Main Firmware v01.41 Lançado em
- Box A11E Rev HW Adicionado
- Pequenas mudanças e correções de bugs

Modo Clip Como executar "?
1. Anexar Clip Adaptador para caixa Port "diagnóstico"
2. Ligue Clip Adapter "cabo USB" para a caixa de entrada USB
3. Conecte uma bateria 9V para Clip Adapter
4. Conectar-se ao telefone "Service Port"

Modo Clip Como usar "?
Depois Clip Mode é executado, você precisa usar o botão S1 para mudá-lo de modo.
O modo padrão do clip é a seguinte:
RED (lentamente piscando) - leia as informações via telefone FBUS
outros modos você pode selecionar pressionando o botão S1:
GREEN - Unlock / Repair simlock
BLUE - Código de segurança reset / tentativas sec.code

Uma vez que modo correto é atribuído, você precisa pressionar o botão S2. medidas necessárias serão tomadas, e greeen (sucesso) ou vermelho (não) piscará afterall rápido. Clip estará pronto para o serviço de telefone seguinte modo / selecionar outros / etc.

Talvez alguns filmes, como usá-lo?
Youtube: YouTube - Cyclone Box usado como clip com as mais recentes addon

Onde obter o hardware clipe?
Você pode perguntar a qualquer um dos Cyclone Box distribuidor / revendedor.
Hardware é relativamente barata - 15 dólares (preço final).
Vamos atualizar clip em breve com outras funções.
É o primeiro oficial Cyclone Addon.
Mantenha nota é CYCLONE ADDON, e mesmo Clip Adaptor - é apenas uma placa e ainda Cyclone Box é necessário para o trabalho!

Sempre de download?
RapidShare: 1-Click Web hosting - Easy Filehosting

Atenciosamente,
Fique atento,
Ciclone Team

[ticocell]

Amigos Estou Com A Minha Cyclone Que Não Desbloqueia Dct4 Aparece Error (0x,02) ???
Alguem Pode Me Ajudar ?

[derbetty]

Postado Originalmente por ticocell

Amigos Estou Com A Minha Cyclone Que Não Desbloqueia Dct4 Aparece Error (0x,02) ???
Alguem Pode Me Ajudar ?

Topico exclusivo apenas pra atualizações da Box , crie um topico especifico com sua duvida OK

[derbetty]

Cyclone Box Firmware v01.42 Released
Hi, new Cyclone Firmware is uploaded on server.

- Fixed particular problems with handling new loaders (10.18.00), however if you still having problems with flashing phones using new protocol no need to make headache - we though about it and left old protocols untouched, so in case just make bugreport in our subsection and meanwhile you can flash your unit by ticking "Use Old Protocol Loaders".
- Minor changes and bugfixes

Every box have 3 update credits, please be patient during upgrade.
No need to upgrade EXE - bug was inside box fimware, not in EXE, so just use Box Maintenance and upgrade box microcode.

Best Regards,
Cyclone Team

[derbetty]

Cyclone Box Firmware v01.43 Released
Hi, New firmware v01.43 is uploaded to server

- Fixed "Smartcard is not responding for reset" in some configurations. Thanks TouTouGSM for reporting and helping in removing this problem. ([Somente usuários registrados podem ver os links. Clica aqui para se registrar...])

Please upgrade your box only if you are encountering Smartcard problems, else no upgrade is needed.

Don't need to upgrade exe if you have installed latest installer (released on 01.07.2010), else install this installer to have backward Nokia Loaders compatibilty. To upgrade just go to "Box Maintenance" and use Maintenace to write latest microcode.

As always,every box having 3 update credits. Please WAIT PATIENTLY during upgrade as it will end (else your box will not be upgraded, and credits will be charged, you will need to ask us agian, etc, etc - so just click BOX MAINTENANCE and patiently WAIT!).

During upgrade you may see message like "Cant upgrade bootloader", "Not allowed to upgrade bootloader", "Bootloader upgrade skipped". THIS IS VERY NORMAL becuase BOOTLOADER SHOULD BE UPDATED ONLY ONCE to minimise risk of destroying your box. As you know bootloader is first code executed upon box bootup, so when its corrupt/destroyd box is bricked. So if your bootloader is already up to date you will receive such message, but that means everything is just fine.

Another things which need attention is usage latest firmware and latest NK loaders.
Keep note that firmwares >=v01.42 need have installed Nokia loaders 10.18.00 (latest installer update). Else you will encounter booting and flashing problems - firmware >=01.42 is not compatible with 0.9.50 loaders !!! So if you don't installed latest installer BUT upgraded Firmware to >=v01.42 YOU WILL ENCOUNTER NOKIA BB5 FLASHING PROBLEMS!

Just sticky with this rules and enjoy Cyclone

Best Regards,
Cyclone Team

[Beni Amaral]

Cyclone NEVER SLEEP Installer v1.08 - New FBUS Loaders v10.20.1, Firmware v01.45...

Hi, that's is right time
New Cyclone Installer,Firmware,Loaders are avaiable.

What's new?
=====================
Installer v1.08
06.07.2010
=====================
- Added new Nokia FBUS Loaders for Old and New protocols (v10.20.0)
- Fixed problems with flashing RAPIDO based phones with hash 479.... (N86,X6). Was Nokia fault (10.18.0 loader pack was broken, probably problem with RSA signature so loader wasn't spawned at all...)
- Fixed problem with FUR initialization when dealing with v10 (2010) Nokia Loaders (Affected was new protocol phones)
- Forced users to install v1.08 changing few firmware routines - some users upgraded their boxes updating it for "v10" loaders, but they didn't installed new installer - their BB5 flashing was broken then. Forcing users to install v1.08 and upgrade box is just to ensure every user will have 100% working environment (latest loaders, latest firmware, latest exe).
- New Box Firmware v1.45 Released
- Handling some smartcards in main firmware fixed
- Minor changes and bugfixes

Where to download?
[Somente usuários registrados podem ver os links. Clica aqui para se registrar...]

Don't forget to upgrade your box firmware to v01.45 !

Best Regards,
Stay Tuned,
Cyclone Team

[Beni Amaral]

A SURPRESA DO ANO!!

Cyclone Box Installer v1.09 Released, SL3 Unlocking Added, New FBUS Loaders, and more!!
Hi!
New update for Cyclone Box is Ready.

What's new?

Code:
=====================Installer v1.0902.08.2010=====================
- New BB5 Loaders v10.22.00 Introduced
- SL3 Unlocking added, uses server and credits, supported models:
- 2700 Classic (RM-561)
- 2730 Classic (RM-57)
- 2730c-1b (RM-579)
- 2690c (RM-635)
- 3600 Slide (RM-352) v56.26 – v57.23
- 3720 Classic (RM-51)
- 5130 XpressMusic (RM-495)
- 5310 XpressMusic (RM-303) v58.58 – v59.42
- 5730s (RM-465)
- 6300 (RM-217) v57.20
- 6303 Classic (RM-443)
- 6500 Slide (RM-240) v59.60
- 6500 Classic (RM-265) v59.45
- N97 (RM-505/506/507)
- N97 mini (RM-555)
- When using New Protocol flashing, software reminds about correct TX2 cable and yellow adapter
- Added Manual Mode to retrieve SL3 NCK if you dont have phone in hand (just enter IMEI when asked)
- Added "Erase NCK Codes"
- this should be used when phones needs to be factory
-relocked (best to use with SL3 if you want to clear entered NCK codes). Work with SL2 too. Simlock area is untouched when Relocking to factory state, and warranty will still be ok. Seems first software on market with such funcionality.
- Fixed BlackBerry calculation problems, old version never closed TCP connection after success or non-success calculation
- Firmware v1.46 Released, Added SL3 Routines
- Minor changes and bugfixes

Example SL3 unlocked by new update

Code:
BB5 Unlock Started...
MCU Version V 07.95MCU Date 03-02-10Product RM-495
Manufacturer (c) Nokia IMEI 351538045311523
Mastercode 4612735731
Simlock Server SIMLOCK SERVERSimlock Key 2600300000000000
Simlock Profile 8000000000000000
Simlock Key Cnt 0
Simlock FBUS Cnt 0
Simlock [1,1]
State: CLOSED
Type: MCC-MNC
Data: 26003F
Connecting to Cyclone Server...
Cyclone Server (1.0.0.632), Cyclone Box Team 2008, 2009, 2010
- Ready.Checking job status...
Code Ready, Code: #pw+966057384237461+7#
Sending code via FBUS...
NCK[7] - ACCEPTED
Code Accepted!
Unlocking Finished!

Where from download?
[Somente usuários registrados podem ver os links. Clica aqui para se registrar...]

A firmware upgrade to v1.46 is needed to use this update!

Stay tuned,
Best Regards,
Cyclone Team

[Beni Amaral]

CycloneBox Blackberry module updated

ALL LATEST PHONES WITH NEW SECURITY ARE SUPPORTED NOW WITH CYCLONE BOX (BY IMEI AND CABLE)

HERE IS THE LIST OF SUPPORTED MEPS


MEP-16826-001
MEP-17232-001
MEP-17490-001
MEP-17568-002
MEP-18601-001
MEP-18637-001
MEP-10073-001
MEP-10129-001
MEP-10129-002
MEP-10129-003
MEP-10129-004
MEP-10129-005
MEP-11016-001
MEP-11139-001
MEP-11139-002
MEP-11139-003
MEP-11139-004
MEP-11139-005
MEP-04103-001
MEP-04103-002
MEP-04103-004
MEP-04104-003
MEP-04104-004
MEP-04104-005
MEP-04104-006
MEP-04104-007
MEP-04546-001
MEP-04598-003
MEP-04598-004
MEP-04598-005
MEP-04626-001
MEP-04626-002
MEP-04938-001
MEP-04938-002
MEP-05277-001
MEP-05277-002
MEP-05277-004
MEP-05277-005
MEP-06041-001
MEP-06041-003
MEP-06041-004
MEP-06041-005
MEP-06041-006
MEP-06041-007
MEP-06041-008
MEP-06041-009
MEP-06041-010
MEP-06068-001
MEP-06068-002
MEP-06259-002
MEP-06259-003
MEP-06423-001
MEP-06424-001
MEP-06424-002
MEP-06529-001
MEP-06529-002
MEP-06530-001
MEP-06530-002
MEP-06810-002
MEP-06811-003
MEP-06812-001
MEP-06812-003
MEP-06812-004
MEP-06813-001
MEP-06813-002
MEP-06814-001
MEP-06814-002
MEP-06814-004
MEP-06814-005
MEP-06849-001
MEP-06849-002
MEP-06893-001
MEP-06899-001
MEP-06899-002
MEP-07321-002
MEP-07484-001
MEP-07484-002
MEP-07484-003
MEP-07484-004
MEP-07484-005
MEP-07484-006
MEP-07484-007
MEP-07705-002
MEP-07705-003
MEP-07722-001
MEP-07722-002
MEP-07722-003
MEP-07723-001
MEP-07723-003
MEP-07723-004
MEP-07723-005
MEP-07723-006
MEP-07723-007
MEP-07754-001
MEP-08209-001
MEP-08209-002
MEP-08209-003
MEP-08318-001
MEP-08395-001
MEP-08448-001
MEP-08448-002
MEP-08589-001
MEP-08881-001
MEP-08882-001
MEP-08918-001
MEP-09004-001
MEP-09070-001
MEP-09149-001
MEP-09292-001
MEP-09292-002
MEP-09292-003
MEP-09292-004
MEP-09292-005
MEP-09293-001
MEP-09625-001
MEP-09667-001
MEP-09690-001
MEP-09747-001
MEP-09783-002
MEP-09783-003
MEP-09821-001
MEP-09821-002
MEP-09821-003
MEP-09917-001
MEP-09938-001
MEP-11139-006
MEP-11246-001
MEP-11246-002
MEP-11414-001
MEP-11414-002
MEP-11534-002
MEP-11534-004
MEP-11534-005
MEP-11534-006
MEP-11534-007
MEP-11534-008
MEP-12186-001
MEP-12209-003
MEP-12209-004
MEP-12209-006
MEP-12209-007
MEP-12209-008
MEP-12488-001
MEP-12565-001
MEP-12579-001
MEP-12579-002
MEP-12599-003
MEP-12622-002
MEP-12907-002
MEP-12978-001
MEP-12980-001
MEP-12980-002
MEP-13188-001
MEP-13188-002
MEP-13188-006
MEP-13188-007
MEP-13188-008
MEP-13188-010
MEP-13710-001
MEP-13928-001
MEP-13928-002
MEP-13988-001
MEP-13990-001
MEP-14052-001
MEP-14052-002
MEP-14074-001
MEP-14074-002
MEP-14074-003
MEP-14150-001
MEP-14260-001
MEP-14260-002
MEP-14896-001
MEP-14896-002
MEP-14896-003
MEP-14896-004
MEP-14896-005
MEP-15159-001
MEP-15159-002
MEP-15326-001
MEP-15326-002
MEP-15343-001
MEP-16272-002
MEP-16272-003
MEP-16272-005
MEP-16352-001
MEP-16419-001
MEP-16472-001
MEP-19322-003
MEP-19877-001
MEP-20099-002
MEP-20099-004
MEP-20099-009
MEP-20166-001
MEP-20454-001
MEP-20669-001
MEP-21545-001
MEP-21878-001
MEP-22793-001
MEP-23361-001
MEP-24124-001
MEP-24409-002
MEP-24660-001
MEP-24667-001
MEP-24667-002
MEP-24723-001
MEP-24723-002
MEP-26594-001
MEP-26900-003
MEP-27488-001
MEP-27501-003
MEP-28240-002
MEP-28364-001
MEP-28555-001
MEP-29080-002
MEP-29318-001
MEP-30218-001
MEP-30218-002
MEP-30638-001
MEP-30669-001
MEP-31845-001
MEP-33006-002

NOTE : This is sever side update , you dont have to download or do anything

[Beni Amaral]

Oi,
nossos servidores e sistema é atualizado agora. Fila é aberto, porém com uma certa quantidade limitada de slots.
Após o sucesso da rotação máxima do telefone upload é de 48 horas, geralmente pode ser depois de 5 minutos mais ou menos assim.
Quando todos os slots estão ocupados, você receberá uma mensagem sobre este assunto. Apenas mantenha o tryin ', porque depois de terminado um telefone na fila (5-30min), o usuário pode fazer upload de um novo.

Fique atento, o poder laranja está aqui esperando por explosão ... e nós não precisamos usar fonte grande, que ele, mesmo que não precisa usar qualquer fonte, só precisamos liberar as atualizações

PS. Por favor, não tente entrar em contato comigo em PM ou Sonork, eu não usá-lo mais (ainda).
Única forma de entrar em contato comigo agora é ICQ, sou muito ocupado com coisas novas para visitar o fórum e responder 50 PMs por dia. Obrigado pela compreensão.

Atenciosamente,
Ciclone Team